Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 21

Thread: Tilite wheelchair front wheels help me

  1. #11
    Send it back. It could be something wrong with the rear wheel mounting.
    I have had periodic paralysis all my life. I lost my ability to walk in 2011 beginning with a spinal block, which was used for a hip fracture caused by periodic paralysis.

  2. #12
    Looking at the second photo, to me the gap looks to be more like 5mm than 0.5mm. Just saying...

  3. #13
    Senior Member pfcs49's Avatar
    Join Date
    Aug 2013
    NW NJ ***********T12 cmplt since 95
    Quote Originally Posted by Rowan View Post
    Looking at the second photo, to me the gap looks to be more like 5mm than 0.5mm. Just saying...
    that occurred to me also.
    69yo male T12 complete since 1995
    NW NJ

  4. #14
    My ZR has the same issue. Nobody would fix it, the back and forth just dragged on. It causes extreme flutter, and it sucks.

  5. #15
    Senior Member
    Join Date
    Nov 2012
    Southeast, USA
    Quote Originally Posted by rAdGie View Post
    not in a brand new chair i wouldnt ... would you?
    Under certain circumstances yes, because I've done it. I had to send my last TR3 frame back once to fix a screw up. After I finally got the 2nd frame, one of the casters floated like that (as well as a few other minor issues) and there was no way I was sending it back again to wait a month and then get a third frame with something else wrong. So I put some washers in and its been fine for years. The cap at the top of the fork covers them up for the most part, so its not noticeable. It's just extending the length of the fork, not changing the angle, so I don't see any problem with it.

  6. #16
    I agree with brad spacer washers. Trying to get Ti lite to cover a tweaked frame is going to be tough. However it is definitely the first thing I would try.

  7. #17
    Before you make any changes, make sure your rear tires are equally inflated-a low tire on the opposite rear can make a caster float.
    Also, if it only floats sometimes, it is quite likely the floor isn't flat.
    Hope this helps.

  8. #18
    It looks like the caster angle is off. If you rotate just that caster around if it gets closer to the ground or farther away it's out. And if one is the other might be.

  9. #19
    Senior Member
    Join Date
    Jan 2015
    NB, Canada
    I would make sure that the front casters are both square as well as the rear wheels as well as being properly inflated. In fact, all wheels should be square/aligned on any wheelchair. If you are still experiencing the same problems on a hard level surface, than that tells me that the frame is crooked. I don't envy fighting with a wheelchair manufacturer to get it fixed. In my experience, once they make the sale, they don't want to hear from you again unless you are ordering another chair. Good luck.

  10. #20
    WHY is it SO hard to get them to rectify something that is their fault?? I just don't get it. They used to try to fix things, sending new caster forks to see if it helped and such. But then this past chair, they just said talk to the DME, don't come to us.

Similar Threads

  1. FS: SPOX Wheels, Tilite Wheels, Tilite Armrest, Tilite Backrest
    By talagaja in forum Equipment & Services
    Replies: 7
    Last Post: 02-16-2018, 03:00 PM
  2. Tilite 2GX Wheelchair 17 x 18 with 24 inch wheels
    By Curt Leatherbee in forum Equipment & Services
    Replies: 1
    Last Post: 12-06-2016, 08:45 PM
  3. Replies: 1
    Last Post: 05-27-2013, 08:06 PM
  4. Replies: 3
    Last Post: 03-30-2013, 12:47 AM
  5. Replies: 1
    Last Post: 11-14-2008, 11:58 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts