Search:

Type: Posts; User: radio_buddha

Page 1 of 26 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    55
    Views
    23,685

    An eighth of an inch of carbon fiber for 113...

    An eighth of an inch of carbon fiber for 113 pounds is overkill.

    Get aluminum at 1/8 of an inch from onlinemetals.com in the dimensions you need and save yourself a lot of hassle and money.
  2. Replies
    16
    Views
    5,723

    And removing toenails?

    And removing toenails?
  3. Replies
    4
    Views
    1,349

    Terminator from Top End.

    Terminator from Top End.
  4. Replies
    4
    Views
    1,349

    Fusion 16 axles for Terminator T6

    I found a couple of fusion 16 wheels in my garage.

    They look really nice. I went in to replace my spinergys and...

    It did not work. The hub is significantly more narrow on the fusion16. I...
  5. Replies
    2
    Views
    1,357

    So nothing? Thanks guys.

    So nothing? Thanks guys.
  6. Replies
    2
    Views
    1,357

    Non-hydraulic vehicle

    I ride in a 2009 Chrysler Town & Country. It's beautiful. Electronic ignition. Side entry. Vehicle lower 6 inches to enter. The ramp is to controlled from the drivers side or the keychain.

    And...
  7. I'll trade you my used underwear and pay for...

    I'll trade you my used underwear and pay for shipping.

    Seriously, how much did you pay for it. I'm guessing a vanishingly small number.
  8. Replies
    2
    Views
    1,628

    Thank you for the suggestion. I looked them up...

    Thank you for the suggestion. I looked them up and had a nice conversation.

    I'll stop by on Monday.

    I already ordered a new one but it would be nice to have 2 functional batteries.
  9. Replies
    2
    Views
    1,628

    Molift batteries

    I have a Molift Smart 150.

    It has a 14.4 volt battery.

    From everything I can see, it looks like a power drill battery. Batteries for power drills are considerably cheaper than any kind of...
  10. Replies
    2
    Views
    747

    After some assertive pushing on the phone, I...

    After some assertive pushing on the phone, I discovered that the fork bearings of the top end terminator are 1616-2RS.



    Does anybody know about a ceramic equivalent? I can’t seem to find any.
  11. Replies
    2
    Views
    747

    Topend Terminator forks

    A few days ago, my right fork jammed.

    I checked it out by taking off the caster, removing the nut and then… Stuck.

    I examined the joint and it looks like a lot of black crap is in there.
    ...
  12. Replies
    32
    Views
    11,343

    I've tried out the Alpha grips. Almost works for...

    I've tried out the Alpha grips. Almost works for me. Not having anything around the wrist kills it within a few minutes. It could be good for somebody. Just not me.
  13. Replies
    8
    Views
    1,438

    Whoever writes the manuals should remain...

    Whoever writes the manuals should remain anonymous for their personal safety. :-)

    I've got the big wrench covered. I bought a 1 1/8 craftsman wrench on ebay not too long ago just for this...
  14. Replies
    8
    Views
    1,438

    I'm working on narrowing the rear wheel spacing....

    I'm working on narrowing the rear wheel spacing.

    Adjusting the rear wheel spacing has been on my list for too long.

    Right now, it's 1.4 inches. I want to bring it to 0.75.
  15. Replies
    102
    Views
    21,406

    Be cool. Ask for them to cut it in the kitchen. ...

    Be cool. Ask for them to cut it in the kitchen. Leave above 30%. How valuable is your time? Money makes the world go round. If you're going to go out, think about what you will need to ask for.
    ...
  16. Replies
    9
    Views
    2,132

    It might not be TI Lite's fault (full disclosure:...

    It might not be TI Lite's fault (full disclosure: I have a borderline hatred for the company.)

    Governments may not like an open market for medical equipment. In spite of trade treaties, medical...
  17. Replies
    14
    Views
    4,402

    T6 Aluminum is cheaper, has more than enough...

    T6 Aluminum is cheaper, has more than enough strength for the application and doesn't degrade when exposed to sunlight.
  18. Replies
    8
    Views
    1,438

    Topend Terminator users…

    I want to bring my wheelbase in.

    Page 58: http://www.topendwheelchair.com/TopEnd_Media/TopEndProductDocuments/1171801~A~00%20Terminator.pdf

    According to the directions, I don't need to turn the...
  19. Replies
    2
    Views
    1,133

    Icon in the wild

    At yesterday's NASCAR Homestead 400, I saw a guy using an Icon. Looked like half an inch clearance beneath his heels. Otherwise, nice chair.

    Is the foot plate angle adjustable?
  20. If you have windows seven, speech recognition is...

    If you have windows seven, speech recognition is free. Just add a good microphone and be vigilant about error correction. The system learns quickly.

    The macro system is well documented on the...
  21. Replies
    11
    Views
    2,452

    8 years. I get new cushions every 18 months. ...

    8 years. I get new cushions every 18 months. They are excellent. No skin issues.
  22. Replies
    20
    Views
    4,058

    TopEnd. Terminator. Excellent chair. Strong,...

    TopEnd. Terminator. Excellent chair. Strong, easy to maintain. The staff is accessible to customers which is TI Lite 's major problem.

    Consider the cost of parts. Want to move your chair...
  23. Dragon Dictate became a major problem for me...

    Dragon Dictate became a major problem for me before windows seven. It's a very old piece of software and, as a software developer, I can't stick around old hardware just because it works for me. ...
  24. Use Voice commands with XCOM: Enemy Unknown

    I created a Windows 7 speech macroset for XCOM: Enemy Unknown.

    Here it is: http://chrisuzal.com/stuff/XCOM_Enem...WSR_macros.zip

    Read the XCOM_Enemy_Unknown.WSRMac file. It is a text file....
  25. Thanks but that won't work because I have a...

    Thanks but that won't work because I have a modified push to lock setup that requires the top end equipment configuration: http://sci.rutgers.edu/forum/showthread.php?t=178780&page=2
Results 1 to 25 of 637
Page 1 of 26 1 2 3 4