Search:

Type: Posts; User: Oddity

Page 1 of 146 1 2 3 4

Search: Search took 0.15 seconds.

  1. Thread: New CareCure

    by Oddity
    Replies
    8
    Views
    127

    Everything should transfer over. Working on...

    Everything should transfer over. Working on photos and avatars now.
  2. Thread: roho repair?

    by Oddity
    Replies
    5
    Views
    126

    Those patches installed properly will last fine. ...

    Those patches installed properly will last fine. I get new holes before patches fail. Never had one fail really. Even placed on seams between cells and the base. Follow their instructions and...
  3. Replies
    15
    Views
    578

    I choose my most recent chair because I was...

    I choose my most recent chair because I was curious how close I could get to the fit and performance of my $7,000 Lasher Sport BT-Mg for as close to 1/10th the cost as possible. I choose the BT-Mg...
  4. Replies
    15
    Views
    578

    Our experiences are precisely why we shouldn't be...

    Our experiences are precisely why we shouldn't be left to make decisions based on inferences taken from single/small sample anecdotes and "personal experience". Your favorite chair that lasted 15...
  5. Replies
    15
    Views
    578

    I really don't think frame material matters. I...

    I really don't think frame material matters. I think we mostly perceive what we want to perceive and take material properties from MDS and other industrial applications and errantly apply them to...
  6. Replies
    15
    Views
    578

    my question remains, and has always been, given...

    my question remains, and has always been, given what I can get off the MDS for annealed (workable) 6al4v titanium vs heat treated 7000 series aluminum, the titanium is ~45% stronger but 60% heavier...
  7. Replies
    15
    Views
    578

    I thought titanium was heavier than aluminum? ...

    I thought titanium was heavier than aluminum? Atomically speaking I'm pretty sure it is. Only "lighter" when you use less of it because it's stronger. But when you do that it isn't (much if at...
  8. Replies
    10
    Views
    794

    I'm comparing my TiLite upholstery to some light...

    I'm comparing my TiLite upholstery to some light weight 64gsm ripstop nylon I have on hand (wife made a rain poncho out of it) and the TiLite stuff seems lighter. I dunno just eyeballing it really. ...
  9. Replies
    10
    Views
    794

    It's pretty low. Like 25-35 GSM at best. Very...

    It's pretty low. Like 25-35 GSM at best. Very low denier as well because the individual threads are tiny. Just guesstimating based on some TiLite upholstery I have compared to the 64GSM nylon I...
  10. Replies
    10
    Views
    794

    Since denier is about individual threads, also...

    Since denier is about individual threads, also consider gsm (grams per square meter). A high denier can still have a low gsm, meaning the weave is not very dense, so often won't be as strong/stiff...
  11. Replies
    10
    Views
    794

    I've bought this from Joanne before ...

    I've bought this from Joanne before

    https://www.joann.com/rip-stop-nylon/xprd560961.html

    Works.
  12. Replies
    27
    Views
    1,028

    One thing to note about caster angle and...

    One thing to note about caster angle and flutter...

    A fork angle that isn't perpendicular to the floor can actually increase the stability at the cost of agility. A caster angle that is off a bit...
  13. Replies
    27
    Views
    1,028

    Yes. Wheelbase is probably the most significant...

    Yes. Wheelbase is probably the most significant variable in the turning agility equation, assuming everything else is in good working order (bearings, etc.)
  14. Replies
    6
    Views
    289

    That is for running a 4K capture card in addition...

    That is for running a 4K capture card in addition to a GPU, and capturing a 4K video stream, not merely outputting 4K to a monitor. Using hardware acceleration in a GPU (which significantly offloads...
  15. Replies
    7
    Views
    664

    Manufacture home and "mobile home with a...

    Manufacture home and "mobile home with a foundation" are very different things. Manufactured homes are built like any other just mostly off premises then assembled on site in large sections. They...
  16. Replies
    27
    Views
    1,028

    It depends on the chair. This one might not be...

    It depends on the chair. This one might not be too bad. I've always had to break out the carpenter's square and get it up on a table to fiddle with it to get it exact. Eyeballing it is fine I goes...
  17. Replies
    27
    Views
    1,028

    Ronnie, If you're not familiar with what this...

    Ronnie,
    If you're not familiar with what this means, at the factory they make sure the vertical axis of the fork is perfectly perpendicular to the floor, so when the fork rotates around 360deg the...
  18. I heard it should be ready to cure us all in...

    I heard it should be ready to cure us all in about 5 years. ;)
  19. Replies
    27
    Views
    1,028

    Yeah. Good seating therapists are hard to find...

    Yeah. Good seating therapists are hard to find it seems. Giving advice on stuff like that over the interwebnets is tough, too. I feel a certain amount of 'personal liability' that pushes me to say...
  20. Replies
    27
    Views
    1,028

    Solutions that require changing your prescribed...

    Solutions that require changing your prescribed seating position are less than ideal, IMO. That will create changes in joint angles, posture, and pressure distribution. I'd just flip the camber...
  21. Replies
    27
    Views
    1,028

    Can you flip the camber tube clamps around to...

    Can you flip the camber tube clamps around to face the other direction? Sometimes that'll squeeze a little more out of it, if they're facing toward the rear to begin with.

    Edit: sorry was...
  22. Replies
    16
    Views
    642

    180Medical always did right by me. Never any...

    180Medical always did right by me. Never any issues or late or missed shipments. Monthly email to confirm shipment. Even worked with me on an out of pocket deal so I could have more than the...
  23. Replies
    2
    Views
    332

    You don't. It's a protected trait. It's no more...

    You don't. It's a protected trait. It's no more a "surprise" than your age or gender or religion. It only becomes relevant after you've been hired and their legal obligations for reasonable...
  24. Replies
    7
    Views
    1,059

    Yeah, and if you're having issues, then put them...

    Yeah, and if you're having issues, then put them all around not just your room. I'd really like some new external lighting and cams, myself. Not so much inside, it no reason not to.
  25. Replies
    203
    Views
    232,467

    Damn Mize that was a fast taper! I titrated down...

    Damn Mize that was a fast taper! I titrated down from 2400mg per day gabapentin down to nothing over 3 months without much trouble, other than the nerve pain coming back. It never really went away...
Results 1 to 25 of 3640
Page 1 of 146 1 2 3 4