• automation's Avatar
    11-11-2018, 06:12 PM
    Makes sense. I had (misread!) thought the final result was printed plastic (note that you can also 3D print other materials -- for a price!). ...
    6 replies | 277 view(s)
  • automation's Avatar
    11-10-2018, 09:06 PM
    Why was a 3D printer required? It looks like a couple of pieces of sheet metal could do the trick (?) How durable is the resulting product?
    6 replies | 277 view(s)
  • automation's Avatar
    11-08-2018, 04:49 PM
    automation replied to a thread Batteries in Equipment
    While excessive (mechanical) force can damage the battery, it seems unlikely that THAT much force would have been present (to deform the battery to...
    38 replies | 6024 view(s)
  • automation's Avatar
    11-08-2018, 04:46 PM
    automation replied to a thread power chair batteries in Equipment
    Likely so -- unless the batteries are the wrong "chemistry" for the charger. Or, the charger is defective. It sure would be nice if...
    11 replies | 443 view(s)
  • automation's Avatar
    11-07-2018, 02:38 PM
    automation replied to a thread Batteries in Equipment
    A shorted cell wouldn't prevent the battery from taking a charge; rather, it would cause the battery's "fully charged" open-circuit voltage to be...
    38 replies | 6024 view(s)
  • automation's Avatar
    11-06-2018, 10:00 PM
    automation replied to a thread power chair batteries in Equipment
    How are you deciding that they are "going dead fairly fast"? Does the gas gauge dip (significantly) when you apply load and then "spring back"? ...
    11 replies | 443 view(s)
  • automation's Avatar
    11-04-2018, 06:09 PM
    You haven't explicitly indicated whether or not any errors are being thrown when this occurs. I'll assume not. I'm not familiar with this...
    1 replies | 151 view(s)
  • automation's Avatar
    11-04-2018, 04:26 PM
    automation replied to a thread Batteries in Equipment
    Heat kills batteries. Well, heat "accelerates the aging of batteries" is probably a less biased way of saying it. Every ~15-18F degree rise in...
    38 replies | 6024 view(s)
  • automation's Avatar
    11-03-2018, 04:09 PM
    automation replied to a thread Batteries in Equipment
    I suspect most "fuel gauges" display some variation of the (instantaneous!) battery voltage. If the gauge truly reflected the state of the battery,...
    38 replies | 6024 view(s)
  • automation's Avatar
    10-30-2018, 02:45 PM
    automation replied to a thread Depressed AF in Care
    Obviously, there are no substitutes for one-on-one contact -- being in the same room with the folk(s) as you're interacting. But, what about...
    30 replies | 1684 view(s)
  • automation's Avatar
    10-29-2018, 08:50 PM
    automation replied to a thread Battery backup in Computers
    One other item that can be important: some UPSs can only be turned on when power is available. Others can be turned on regardless of the...
    5 replies | 766 view(s)
  • automation's Avatar
    10-29-2018, 08:26 PM
    automation replied to a thread Battery backup in Computers
    Our utilities are "below grade", so we tend not to suffer as many outages as other places I've lived. The outages that we do see tend to be...
    5 replies | 766 view(s)
  • automation's Avatar
    10-23-2018, 02:58 AM
    We get ~11 inches of rainfall (no snow) annually. Usually, from significant -- but short lived (hours!) -- storms ("Monsoon Season"). As luck...
    37 replies | 4244 view(s)
  • automation's Avatar
    10-19-2018, 10:36 PM
    automation replied to a thread DME pricing in Equipment
    So, these "buy ups" beg the question:Are "independents" selling out because they are "struggling" (can't make ends meet)? orAre the chains...
    20 replies | 1424 view(s)
  • automation's Avatar
    10-16-2018, 06:39 PM
    automation replied to a thread DME pricing in Equipment
    This is distressing. As a teenager, my vehicle was vandalized (side window broken to gain entry). I called local glass company looking to get the...
    20 replies | 1424 view(s)
  • automation's Avatar
    10-16-2018, 01:57 PM
    automation replied to a thread DME pricing in Equipment
    This sort of "creative pricing" seems to be commonplace throughout the Medical industry. E.g., doctor/hospital bills $400 for blood work -- then...
    20 replies | 1424 view(s)
No More Results
About automation

Basic Information

About automation
Date of injury (NA if not spinal-injured)?:
NA
Location:
AZ
Occupation:
Engineer
Why did you join this forum?:
Advice/research

Statistics


Total Posts
Total Posts
100
Posts Per Day
0.50
General Information
Join Date
04-30-2018
Referrals
0