Tab Content
  • MikeP2013's Avatar
    10-19-2018, 11:26 PM
    MikeP2013 replied to a thread DME pricing in Equipment
    I have no idea. But it would be interesting to know because amount of DMEs were decreasing already and many only dealt with regular powerchairs, no...
    20 replies | 754 view(s)
  • MikeP2013's Avatar
    10-19-2018, 08:34 PM
    MikeP2013 replied to a thread DME pricing in Equipment
    The one that took over our old DME here had the original Tech staff about 6 months and owner was a Manager for little less than a year.
    20 replies | 754 view(s)
  • MikeP2013's Avatar
    10-17-2018, 07:59 PM
    MikeP2013 replied to a thread DME pricing in Equipment
    Sincerely I am so sorry! I miss our independent DME SOOOOOOOOOOOOO badly! Get Demo pick chair within a few weeks chair delivered!!! Longest ever...
    20 replies | 754 view(s)
  • MikeP2013's Avatar
    10-16-2018, 07:54 PM
    MikeP2013 replied to a thread DME pricing in Equipment
    Took me a while but with help with big words I gots it all read up today! Hear ya on window. Had been to dentist in middle of ice/snow storm a few...
    20 replies | 754 view(s)
  • MikeP2013's Avatar
    10-15-2018, 12:09 AM
    MikeP2013 replied to a thread DME pricing in Equipment
    Now I'm the first to admit I ain't bright!!!!!! But, around here big nation wide DMEs are buying up small and independent DME shops. IMHO, as well...
    20 replies | 754 view(s)
  • MikeP2013's Avatar
    10-12-2018, 12:20 AM
    I don't know a thig about manual chairs so this is way over my head. But, just wanted to wish you "Good Luck!"!
    25 replies | 1161 view(s)
  • MikeP2013's Avatar
    10-05-2018, 11:36 PM
    MikeP2013 replied to a thread Portable ramps in Equipment
    IMHO trying to carry ramps on vacation is dangerous for you and whomever that attempts to unload/load on your chair before doors close, etc....
    9 replies | 519 view(s)
  • MikeP2013's Avatar
    10-02-2018, 12:30 AM
    "Thanks!" Went out and started at scratch setting both adjustment screws and pushing hard while tightening. Worked well afterwards. Then tackled the...
    13 replies | 705 view(s)
  • MikeP2013's Avatar
    09-30-2018, 07:45 PM
    "Thank you!" Hoping I'll be up to tackling again in the morning. At least now cover is left off the tower, so can go get groceries without worrying...
    13 replies | 705 view(s)
  • MikeP2013's Avatar
    09-30-2018, 05:26 PM
    Mr. West, Gave it a try and same it Deployed not lower(Down). Released door to be able reach lift tower. ***Used your 'simple test' using screw...
    13 replies | 705 view(s)
  • MikeP2013's Avatar
    09-30-2018, 12:59 PM
    Again, "Thank you!" I read Manual and watched the Installation Video again. Found on Tech Tips the "New" version of the Pressure Solenoid for K...
    13 replies | 705 view(s)
  • MikeP2013's Avatar
    09-29-2018, 09:00 PM
    I'd like to try a Otto Bock chair. I have their backrest 3, I think it;s called with side guards. Great idea with the different bags in back to make...
    11 replies | 900 view(s)
  • MikeP2013's Avatar
    09-29-2018, 08:19 PM
    MikeP2013 replied to a thread new tr3 in Equipment
    Good looking chair! Wish I could still use manual chair. Sure open up more options on vehicles. No need for lift woul be great these days.
    10 replies | 1185 view(s)
  • MikeP2013's Avatar
    09-29-2018, 08:12 PM
    Mr. West, "Thank you!", especially for the link. I know when started to adjust first time done according to manual. Turn screws 6 to 8 turns and...
    13 replies | 705 view(s)
  • MikeP2013's Avatar
    09-29-2018, 03:41 PM
    OK, so you would suggest just re-adjusting the Limit switches for Deploy and be sure to adjust Deploy right below the Up Cutoff(just slight tilt...
    13 replies | 705 view(s)
  • MikeP2013's Avatar
    09-29-2018, 01:22 PM
    Lift and van is old, 15 years old. Have had van is several times for same problem. Off and on deal that lift either not deploy or would deploy but...
    13 replies | 705 view(s)
  • MikeP2013's Avatar
    09-29-2018, 12:41 PM
    Just in case have you contacted dealer and ATC about solutions/ideas on what might work? Or other solutions other than mods?
    32 replies | 1788 view(s)
No More Results
About MikeP2013

Basic Information

Statistics


Total Posts
Total Posts
179
Posts Per Day
0.09
General Information
Last Activity
Today 12:36 AM
Join Date
08-14-2013
Referrals
0